Mobile concrete batching plant Benninghoven TBA-200

Concrete batching plants Benninghoven
 
 
 

Adverts

1000 USD
Used stationary asphalt concrete plant Benninghoven TBA-200 t / h (2009 onwards) BENNINGHOVEN 200 T / H CAPACITY STATIONARY ASPHALT MIXING PLANT “TBA-200” Year of production: 2009 Output: 1000.000 T Oil burner At the moment, the plant is fully operational. Standard conditions: The plant is designed to produce 200 t / h of road mix with a finished product at an initial moisture content of 4% and 160 ° C under the following standard conditions: The temperature of the units at the inlet to the dryer is more than 10ºC Height above sea level Average density of feed aggregates 1,650 kg / m3 Fuel oil No: 6 calorific value ≥ 9.200 kCal / kg Fuel oil No: 4 calorific value ≥ 9.700 kCal / kg Calorific value of diesel fuel ≥ 10.200 kcal / kg Calorific value of natural gas ≥ 7,600 kcal / kg Hot aggregate temperature rise 160 K Residual moisture content in the mixture 0.3% Maximum. unit size 40 mm Passage screen of material 3 mm 35% Passage screen of material 80 m 8% Total specific heat% 0.21 kcal / kg º C Production rate includes all recovered filler and an average of 5% in weight added bitumen The material is non-porous and hygroscopic with a normal shape Manufacturing tolerance according to environmental conditions and parameters ± 10% Aggregate material feeding system 5 pieces. Material hopper Volume: 15 m3 each Loading height: 3.500 mm Mesh 5pcs. These grids of 100 x 100 mm are placed on the aggregate bins to prevent non-standard aggregates and foreign materials from entering the belt. 5 Belt feeders The belt feeders are driven by an inverter controlled gear motor. Narrow knots and idler rollers ensure a smooth belt run. The material flow sensor signals the absence of the unit. Belt width: 650 mm Engine power: 2,2 kW Performance: 100 t / h each 5 Aggregate flow control unit This equipment contains sensors to monitor the flow and / or stop the unit flow for any reason in the aggregate bins. The presence of material is monitored with the help of these detectors. Also, the bins are equipped with beacon sensors located on the bins, with which the operator controls the level of aggregate material in the bins. This avoids a shortage of the unit and loads it continuously and correctly. 5 Control elements of the “2.2 kW” infeed conveyor All power elements, frequency control units and control units are installed in a group control cabinet installed on the cold power supply system. 2 Vibrators for sand bunker, power: 0.26 kW / pc. 1 Collecting conveyor Length: 18.500 mm Width: 650 mm Power dv. : 5.5 Kw 1 Inclined conveyor Length: 12,000 mm Width: 650 mm Power dv. : 7.5 Kw Dryer Drum Type: TT 24 ” Time proportional heating is designed for uniform and high quality drying, and the highest level heating is for low exhaust gas temperatures. Dryer drum (TT. 24) Length: 9.000 mm Diameter: 2.400 mm Drive motors: 4x18,5 Kw 2.2 Air insulation To minimize heat loss. 2.2 Aluminum cladding Aluminum sheathing prevents heat loss. Burner - "BENNINGHOVEN" RAX-JET TURBO 3 Fuel oil 3.1 Basic explanations The burner is a compact monoblock design. The burner is mounted on steel rails, which allows the entire unit to slide back to check the burner and tumble dryer. In accordance with the optimal performance of the dryer, the air flow is generated by an internal radial-axial fan to ensure the best combustion. Main technical parameters The exact proportions of fuel and combustion air are achieved by means of a servo motor. The servo motor activates the oil metering valve and the multi-link air intake via the control levers. Oil is injected by pump pressure into the finest particles to ensure efficient and complete combustion. The burner is made of heat-resistant steel. The control panel includes all monitoring and control equipment along with indicators for monitoring the burner power. The temperature is measured in the drying chute of the dryer with an FE-Constantan fast-acting temperature sensor. Optimum noise reduction is achieved by installing a muffler at the rear of the burner. Burner Type: RAX JET Turbo 3 Fuel oil consumption: 350-1.400 kg / h Heavy-Oil Adjustment range 1: 4 Heavy-Oil Nominal heat output - 16.600 kW (= 14.310.000 kCal / h) Fan capacity: 21.000 m3 / h Air blower pressure
c-equipment.com.ua
2009 yr (used)
Scandinavian & UK Machines
Russia
+38 050 738 33 48
1000 USD
Used stationary (fast-erected) asphalt concrete plant Benninghoven TBA-200-K / U 160 t / h (1993 onwards) Germany In 2002, a cap was carried out. repair Output: 1,000,000 t At the moment, the plant is fully operational. Standard working conditions: The plant is designed to produce 160 t / h of road mix with a finished product at an initial moisture content of 4% and 160 ° C under the following standard conditions: The temperature of the units at the inlet to the dryer is more than 10ºC • Height above sea level • Average density of feed aggregates 1,650 kg / m3 • Fuel oil no: 6 calorific value ≥ 9.200 kCal / kg • Fuel oil no: 4 calorific value ≥ 9.700 kCal / kg • Calorific value of diesel fuel ≥ 10.200 kcal / kg • Calorific value of natural gas ≥ 7,600 kcal / kg • Temperature increase of hot aggregates 160 K • The content of residual moisture in the mixture is 0.3% • Maximum. unit size 40 mm • Passage screen of material 3 mm 35% • Passage screen of material 80 m 8% • Total specific heat% 0.21 kcal / kg º C The main difference between the asphalt concrete plants of the TVA type is the design of their main components, which corresponds to the dimensions of a standard (20- or 40-foot) shipping container, which ensures their easy transportation by truck, sea or rail.
c-equipment.com.ua
1993 yr (used)
Scandinavian & UK Machines
Russia
+38 050 738 33 48
  Add advert